Click here for
B-stock specials
BUY DEALER DIRECT  ---Toll free  888.718.0300----      
  Web sales open 24/7 - No commission salespeople!
 
Categories
  • OPEN BOX SPECIALS
  • Free Studio Gear*
  • Drum Electronics
  • Acoustic Treatment
  • Audio Interfaces
  • Blank Media
  • Cables
  • Compressors
  • Control Surfaces
  • Converters
  • Effects
  • Equalizers
  • Headphones
  • Microphone Stands
  • Microphones
  • Midi Controllers
  • Midi Interfaces
  • Mixers
  • Monitors
  • Patchbays
  • Power Amps
  • Power Conditioners
  • Preamps
  • Recorders - Players
  • Software
  • Studio Furniture
  • Synthesizers
  • Tutorials
  • Word Clock & Sync

  • Manufacturers
  • Shop by Brand
  • Links to our Mfr.'s

  • Special
  • Gift certificates

  • Help Center
  • Contact us
  • Payment options
  • Disclaimer
  • Ensure E-Mails
  • Make an Offer
  • Return Policy
  • Privacy Statement
  • International Policy
  • About Us


  • Except WA. State
    You are hereHome > Headphones > Headphone Amplifiers > HA-6AB

     ·  

    Furman HA-6AB

    Furman HA-6AB - Headphone Amp/20W-channel, Power Amp, Balanced
    View Detailed Image(s)

    17%
    The HA-6A Headphone/Monitor Amplifier is a unique combination of a headphone amp and a conventional power amp. This combination of functions can save the expense of an extra power amp in many recording studios.

    The HA-6A is basically an economical 20 watt per channel stereo amplifier. Unlike a conventional power amp, however, it has six headphone outputs (stereo phone jacks) on the front panel, each with an associated volume control. When used for overdubbing or rehearsal, this provides more than adequate loudness in all headphones (even older low-impedance models), and allows each musician to set his or her own comfortable volume level. When the overdubbing is complete and the musicians remove their headphones, the HA-6A can power the tape playback through either (or both) of two sets of studio monitor speakers, selected by pressing front panel pushbuttons. Without the HA-6A, a separate amp would be needed for the studio speakers.

    The HA-6A also features a convenient input level control on the left side of the front panel. A pair of yellow LED's-one for each channel-light up whenever signal is present (threshold -28 dBu). Another pair of red LED's show an overload condition in either channel.

    The Furman HA-6A's 20 watts-per-channel make it ideal as a low distortion headphone driver for the most critical listening situations. While most headphone amps provide half a watt or less per headphone channel, the HA-6A's higher power can drive headphones of any impedance to their full rated listening level, and do so with minimal noise and distortion. Its power capacity is also just right for the small "cube" reference speakers used in most recording studios as a comparison with the main control room monitors-it can power them without overpowering them. On the studio floor, a set of small monitor speakers driven by the HA-6A can make a session progress more efficiently by giving the musicians a chance to hear a playback without needing to disconnect themselves from their equipment and walk into the control room.

    The HA-6A utilizes an efficient toroidal power transformer for silent operation and low magnetic leakage, as required in a studio environment. It is fully protected against thermal overload, and it can withstand a short circuit on any or all outputs for an indefinite time without damage.

    Powers headphones AND speakers
    New toroidal transformer for studio-quiet operation and low magnetic leakage
    20 watts per channel, stereo
    6 headphone outs, each with volume control
    Switches for two sets of speakers
    Automatically switches to mono mode when right channel is not used
    Overload and signal-present LED's for each channel
    Ground lift, on-off switches; power-on indicator
    Provision for remotely located volume controls

    Power:
    20 watts per channel, stereo, into either 4 ohms or 8 ohms, 20 Hz to 20 KHz.

    Connectors:
    Speakers A: 5-way binding posts (accommodates dual banana plugs, spade lugs, bare wires, etc.) Speakers B/Remote

    Headphone:
    XLR.

    Input Impedance:
    20K ohms.

    Sensitivity:
    -1.9 dBu (625 mV) required for full output into 8 ohms.

    Connectors:
    HA-6A, 1/4" phone, unbalanced; HA-6AB, both phone (unbalanced) and XLR (balanced).

    Distortion:
    .01% THD at full rated power at 1 KHz; .05% THD 20Hz to 20 KHz.

    Dynamic Range:
    Greater than 99 dB

    Frequency Response:
    +0, -1 dB from 20 Hz to 20 KHz, 1 watt output.

    Dynamic Headroom:
    2 dB, stereo, measured with 10 ms tone burst at 1 KHz, 1% duty cycle.

    Power Requirement:
    120 VAC, 60 Hz, 130 watts, and 230 VAC, 50/60 Hz versions available

    Mechanical: Dimensions:
    1.75" H x 19" W x 7.25" D. Weight: 9 lbs (4.2 kg).

    Agency Approvals:
    UL listed; CUL listed; CE listed

     
    Manufacturer's site:http://www.furmansound.com/
    Availability: Usually ships within 24hrs.
    Price: $ 445.00
    Sale price: $ 369.00 (No sales tax outside of WA)

    Found a better price? Give us a call!
    or use the "Make an Offer" option below.
     
    Quantity

            

    OR

    Make an Offer




    FREE GROUND SHIPPING ON MOST ORDERS!
    (Within the continental USA)
    No sales tax to customers outside of WA State.
    Free Ground Shipping!


    Copyright© 1995-2007 Bayview Pro Audio All Rights Reserved.  


     Search: Search  

    > Advanced Search
    Shopping Cart
      
    Cart is empty
      

    View cart
    Secure checkout

    Login
    Username

    Password

    Recover password

    Special Sales
    Enter email address to receive information on our special sales.



    SecurityMetrics Credit Card Safe
     Click here to visit Cascade site